PLEASE CALL US WITH ANY QUESTIONS YOU MAY HAVE - 310.534.1210

MIDGET SHORTIE FRONT HUBS
1008 Midget Aluminum Front Hub Assembly, (Bolt-on) Includes Tirnken bearings, seals, dust covers with o-rings, threaded drive studs and lug nuts. Fits 8503 shortie aluminum spindles.

MIDGET DIRECT MOUNT HUBS
1015-15-3 Midget Direct Mount Front Hubs, Replaces front wheel centers. Includes Timken bearings, seals, dust covers with o-rings studs and lug nuts. Fits S503 shortie aluminum spindles

1015-15-3-1L Midget Direct Mount Front Hub Only, left side.

1015-15-3-1R Midget Direct Mount Front Hub Only, right side.

KING PIN THRUST BEARINGS
S510 King Pin Thrust Bearing Kit, (Both sides) Reduce fric- tion and increase reliability with a Sander needle bearing and hardened washer kit. To be used for all midget and sprint king pin and spindle sets.

S510B King Pin Thrust Needle Bearing Only.
S510W King Pin Hardened Washer Only. (.031)

SPINDLE NUT AND WASHERS
S511 Spindle Nut and Washer Kit, (Both sides) Fits midget (S502) and sprint (S500 & S504) spindles.
S511N Spindle Nut Only
S511W Spindle Washer Only

 

 

 

 

 

S512 Spindle Nut and Washer Kit, (Both sides) Special spindle nuts, locking pins and washers. Fits new type Sander midget spindles (S503) and sprint spindles (S501 & S509).
S512N Spindle Nut Only
S512W Spindle Washer Only
S512P Spindle Locking Pin Only

SANDER LITE KING PINS
S117-0 Midget Lite Tubular King Pin, .812 Diameter to be used with Sander S502 & S503 spindles and S167CB locking cap.

S117 Midget Tubular King Pin, .812 Diameter to be used with Sander S502 & S503 spindles and S167C locking cap.

S167C Locking Cap with 1/2"X 20 thread.

S167CB Locking Cap with 5/8"X 18 thread.

MIDGET HEX NUTS
S479L 1 7/8" Midget Winters Hex Nut, 31 spline rear axle.

S479R 1 7/8" Midget Winters Hex Nut, 31 spline rear axle.

S479LB 2 1/4" Midget Winters Hex Nut, 36 spline rear axle.

S479RB 2 1/4" Midget Winters Hex Nnt, 36 spline rear axle.

KING PIN BUSHINGS TORSION BAR BUSHINGS
S514M Midget King Pin Bushing, fits all Sander front spindles (S502 and S503) and P&S type spindles.

S148MA Midget Aluminum Torsion Bar Bushing, fits 1 1/4" tube with .083 wall.

S149MA Midget Aluminum Torsion Bar Bushing, fits 1 1/4" tube with .095 wall.

S148M-1 Midget 1" Plastic Torsion Bar Bushing, fits 1 3/8" tube with .095 wall.

MIDGET STEERING ARMS
S120 Midget Aluminum Tie Rod Arm, liteweight arnl made from 2024 billet aluminum plate, milled and radius. Hooks tie rod to each spindle.

S121 Midget Aluminum Steering Arm, can be used on the top or bottom of the left front spindle, Drag link hole drilled at 10 degree angle. To be used with two S120 tie rod arms.

S122 Midget Aluminum Combination Arm, for the left front spindle and used with one S120 arm on the right front. Drag link hole drilled at 10 degree angle for better rod end angle.

S122RS Right Steer Combination Arm, for the right front.

MIDGET FRONT BRAKE HATS
1053 Midget Front Brake Hat, billet aluminum to fit a 10.25" rotor (aluminum S559A or steel S559D). Order S518 mounting kit to bolt hat to the back of the front hub.

1053D Midget Front Brake Hat, to fit vented rotor (S558M) to the front hubs. Order one S518 mounting kit to bolt hat to the back of the front hub.

MIDGET FRONT BRAKE BRACKETS
1052 Midget Front Brake Bracket, for use with the single caliper (S566) and a 10.25" rotor left or right front.

1052CSL Midget Front Brake Bracket, for use wth flat aluminum rotor and has flathead bolts for the left front spindle.

1052CSR Midget Front Brake Bracket, for right front spindle.

MIDGET FRONT BRAKE ROTORS
S515M Midget Aluminum Brake Rotor, 10.25" diameter includes mounting kit (S517).

S515MB Midget Aluminum Front Rotor Only.

S516M Midget Steel Brake Rotor, 10.25" diameter includes mounting kit (S517).

S516MB Midget Steel Front Rotor Only.

S558M Midget Front Brake Rotor, vented .810 rotor for use with the Sander 1053D brake hat.

MIDGET ROTOR MOUNTING KITS
S518 Midget Mounting Kit, has three stands threaded 1/2" X 20 thru to fit S115 drive stud and 3/8" X 24 to fit Sander brake hat (1053) and three flat head bolts.
S518-1 Mounting Stand Only
S518-2 Mounting Bolt Only

THREE AND SIX PIN WHEEL SAVERS
S416M Midget Three Pin Wheel Savers, fits midget front hubs.

S417M Midget Six Pin Wheel Savers, Use on the right front wheel on paved tracks.

MIDGET DRIVE PINS DRIVE STUDS AND LUG NUTS
S107 Midget Drive Pin, with 1/2" diameter pin with 3/8" X 24 thread.

S108 Midget Drive Pin Locking Nut, with 3/8" X 24 thread.

S115 Midget Threaded Drive Stud, new type with 1/2" X 13 threaded pin and 1/2" X 20 stud diameter. Used on a11 Sander 1007 and 1008 hub kit.

S110 Lock Nut, with 1/2"X 20 thread for S115 midget drive studs.

S114 Midget Lug Nut, 1/2" X 13 thread fits S112 and S115 Midget threaded drive stud.

FRONT HUB BEARINGS KITS
S133 Front Hub Bearing and Seal Kit, to fit 1008, 1009, and 1015-15-9 front hub assemblies.

Note: All bearing kits come with 2 inboard bearings, 2 outboard bearings, and 2 seals. Order bearings cups separately.

SIX PIN WHEEL SPACERS
S415M Midget Six Pin Wheel Spacer, aluminum wheel spacer .250" wide to fit Midget front or rear six pin hubs.

TORSION BAR STOPS - ALUMINUM AND STEEL ALUMINUM TORSION BAR ARMS
S127 Midget Torsion Bar Stop, aluminum with 7/8" X 48 spline .625" wide, comes complete with bolts

S127-1 Midget Torsion Bar Stop, aluminum with 1" X 48 spline .625" wide, comes complete with bolts.

S126L Midget Aluminum Rear Blank Torsion Arm, with 7/8" X 48 spline .750" wide.

S126-1L Midget Aluminum Rear Blank Torsion Arm, with 1" X 48 spline. 750" wide.

COUPLERS
Once again, a Sander Engineering part that may look similar to others on the market, but in reality is different when you look closely. Our couplers are heat treated and case hardened in special fixtures we made to insure that the final product is not out of round. The whole point of a coupler is that it must be absolutely straight to maintain perfect alignment to prevent vibration and failure.

S170 10-10 Coupler, spline steel coupler.

S170A 10-10 Aluminum Coupler, spline aluminum coupler.

REAR CAM DRIVE KIT
2001 Rear Cam Drive Kit, includes everything needed to reliably drive your power steering, fuel pump or both, off the back of your camshaft. You must drill and tap the end of your cam and cut your motor plate.

REAR CAM DRIVE PARTS
S201 Accessory Rear Cam Drive Housing, this is the 2" deep housing used in our 2001 kit.

S202 Cam Drive, standard right hand threads, 9/16" X 18. Body 1" long, 1 5/8" overall.

S202B Cam Drive, same as the S202 cam drive but with left hand threads.

S202L Cam Drive, long right hand threads, 9/16" X 18. Body 1 1/2" long, 2 1/8" overall.

S202LB Cam Drive, same as theS202L cam drive but with left hand threads.

S203 Cam Seal, includes plate and seal for small block Chevy.

S203R Cam Seal, same as the S203 but for Rodeck Block.

S203RB Cam Seal, for use with a roller bearing camshaft.

S203BB Cam Seal, for use with a big block Chevy.

S203S Cam Seal Only, does not include aluminum plate to fit block.

S204 Intermediate Shaft and Coupler, used in rear drive kit 2001 with 3/8" hex shaft.

S205 3/8" Intermediate Hex Shaft Only.

S206 3/8" Intermediate hex Coupler Only.

S207 1/4" X 20 Allen Bolt, 5/8" long used to bolt S201 housing to motor plate.

TORQUE TUBES
There is a definite difference between a Sander Engineering aluminum torque tube assembly and others on the market. Other tubes on the market are made of 6061 aluminum, which is gummy and not as strong as a Sander torque tube. The Sander aluminum torque tube is made from 2024 drawn aluminum and is .188" wall. That makes a Sander aluminum torque tube stronger. Other products may look the same, but when you look closely, you will see that a Sander product is unique! All Sander Engineering torque tubes are 2.300" O.D. with .188" wall (1.936" I.D.).

S333 Midget Aluminum Torque Tube With Collar, to fit Winters midget rear end with 2.300" tube 26.5", and 27.5" long.

S334 Midget Aluminum Torque Tube With Collar, to fit Halibrand midget rear end with 2.300" tube 26.5", and 27.5".

S335 Midget Aluminum Torque Tube Only, 2.300" diameter.

S345 Midget Aluminum Torque Collar Only.

TUBULAR DRIVE SHAFTS
S164-16 Tubular Drive Shaft, with 16-10 spline. This is the ultimate in strong and superlite weight drive shafts. We stock 20", 22", 24", 26.5", 28", 30", and 32" long.

ALUMINUM U-JOINT
S304A Aluminurn U-Joint Assembly, 7075 billetCNC machined u-joint saves over 2lbs. of rotating weight. Used by all the top pros.

S306A Aluminum Slip Yoke, rear half of our S304A joint.

S308A Aluminum Flange Yoke, front half of our S304A joint.

CRANK FLANGES -U-JOINTS
S301 Chevy Aluminum Crank Flange.

S301B Chevy Aluminum Crank Flange, with bolts.

S304 Steel U-Joint Complete, for use with our crank flanges.

S302 7116" X 20 Allen Head Crank Flange Bolt.

S305 7116" X 20 Thin Hex Head U-Joint Bolt.

S307 U-Joint Cross Only.

CRANK HOUSINGS
S303 Crank U-Joint Adaptor Housing.

S312 U-Joint Adaptor Housing Retainer.

S313 U-Joint Adaptor Housing Retainer Bolt.

S330 Aluminum Ball, for outside 2.300" torque tube.

MIDGET DRIVE LINES
3910 Midget Complete Drive Line, for Winters rearend, with 2.300" aluminum torque tube and aluminum ball. Drive shaft is tubular and is 16 X 10 spline to fit Winters rear end.

3011 Midget Complete Drive Line, for Halibrand rearend with 2.300" aluminum torque tube and aluminum ball. Drive shaft is tubular and is 16 X 6 spline to fit rearend.

MIDGET BILLET BEARING CAGES
4070 Midget Billet Bearings Cages, bearings are 6211RS and come with 31 spline inserts (S477S) to slide on axle.

MIDGET BIRD-BEARING CAGES
4076 Midget Bird-Bearing Cages, with dual pickup (top and bottom). Bearings are 6211RS and come with splined inserts for 31 spline axle.

4077 Midget Bird-Bearing Cages, with dual pickup (top and bottom). This kit is for new Winters 36 spline axle and the bearings are 62l2RS both sides. 

MIDGET AXLE SPACER KITS
S477 Midget Axle Spacer Kit, for 31 spline axle includes 14 spacers for both sides.

S477S Midget Splined Bearing Spacer, for bird-bearing cages. Included with 4076 kit.

S478 Midget Axle Spacer Kit, for 36 spline axles includes 14 spacers for both sides. Note: All Spacers can be ordered separately.

MIDGET BIRD CAGE PLATES
8486L Midget Bird Cage Plate Only, left side with dual pickup for 31 spline axle.

8486R Midget Bird Cage Plate Only, right side with dual pickup for 31 spline axle.

8487L Midget Bird Cage Plate Only, left side with dual pickup, 36 spline axle and 6212RS bearing.

8487R Midget Bird Cage Plate Only, right side with dual pickup, 36 spline axle and 6212RS bearing.



8488 Midget Bearing Cage Only, to fit 6211RS bearing and S486 plates, for 31 spline axle.

8488B Midget Bearing Cage Only, to fit 6212RS bearing and S487 plates, for 36 spline axle.

84888 Midget Bearing Cage Only, to fit 6011RS bearing and S486plates, for 31 spline axle.

84778 Midget 8plined Bearing Insert, fits 6011RS and 6211RS bearing on 31 spline axle.

|